p10 www.vishay.com vishay sfernice revision: 04-jul-17 1 document number: 51030 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 3/8" square panel potentiometer miniature - cermet - fully sealed p10 panel potentiometer comb ines the very good setting stability offered by vishay sfer nice trimmers (due to their proprietary multifinger wiper), with a mechanical life of 10 000 cycles. it is an ideal choice to set and control parameters such as temperature, time, volume levels, etc. features ? industrial grade ? 0.5 w at 70 c ? cermet element ? miniature compact ? plastic housing and shaft ? fully sealed ? 7 standard pin styles ? test according to cecc 41000 or iec 60393-1 ? 10 000 cycles rotational life ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 quick reference data multiple module no switch module n/a detent module n/a special electrical laws no, only a: linear sealing level ip 67 lifespan 10k cycles dimensions in millimeters (inches) 0.5 mm ( 0.02") p10: side adjust p10: top adjust 3 3 x ? 0.5 (0.02) 5.5 (0.22) 2.54 (0.10) ai = 20 (0.79) ag = 16 (0.63) ? 3 (0.12) 4 min. (0.16) m6 x 0.75 2 1 3 2 1 9.7 (0.38) 1.15 (0.05) 2.54 (0.10) 2.54 (0.10) 1 (0.04) 0.6 (0.02) 5.2 (0.20) 5.3 (0.21) 9.6 (0.38) p10xx p10xc 2.54 (0.10) ai = 20 (0.79) ag = 16 (0.63) ? 3 (0.12) m6 x 0.75 1.15 (0.05) 2.54 (0.10) 2.54 (0.10) 1 (0.04) 0.6 (0.02) 5.2 (0.20) 5.3 (0.21) p10xh 1 2 3 2.54 (0.10) 2.54 (0.10) 2.7 (0.11) p10xw 1 2 3 2.54 (0.10) 2.54 (0.10) 2.7 (0.11) 5.5 (0.22) 9.7 (0.38) 9.6 (0.38) 0.6 (0.02) 3 x ? 0.5 (0.02) 5.2 (0.20) 5.3 (0.21) ai = 20 (0.79) ag = 16 (0.63) ? 3 (0.12) 4 min. (0.16) 1 (0.04) m6 x 0.75 2.54 (0.10) 2.54 (0.10) 2.54 (0.10) 4.85 (0.19) 2.25 (0.09) 5.08 (0.20) 2.54 (0.10) 2.54 (0.10) 2.54 (0.10) 2.54 (0.10) 2.54 (0.10) 2.54 (0.10) p10yp p10ye p10ym 3 2 1 3 2 1 3 2 1
p10 www.vishay.com vishay sfernice revision: 04-jul-17 2 document number: 51030 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 electrical specifications resistive element cermet electrical travel 250 15 standard resistance values 100 to 2 m tolerance 10 % - 5 % on request taper linear a power rating 0.5 w at 70 c circuit diagram standard resistance element data standard max. power max. working max. cur. ww v ma 100 0.5 7 70 200 0.5 10 50 500 0.5 15.8 32 1k 0.5 22.4 22 2k 0.5 31.8 16 5k 0.5 50.0 10 10k 0.5 70.7 7 20k 0.5 100 5 50k 0.5 158 3.2 100k 0.5 224 2.2 200k 0.28 250 1.3 500k 0.13 250 0.5 1m 0.06 250 0.25 2m 0.028 250 0.13 temperature coefficien t (typical) 150 ppm/c contact resistance variation (typical) 1 % rn or 2 end resistance (typical) 1 dielectric strength (rms) 1000 v insulation resistance (300 v dc )10 6 m % clockwise shaft rotation 0 20 40 60 80 100 0 20 40 60 80 100 a output voltage ratio (%) ambient temperature in c power in w 0 20 40 60 70 80 100 120 140 0 0.5 a (1) b (2) c (3) cw
p10 www.vishay.com vishay sfernice revision: 04-jul-17 3 document number: 51030 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? nothing stated herein shall be construed as a guarantee of quality or durability mechanical specifications mechanical travel 290 5 operating torque (typical) 2 ncm max. 2.83 oz.-inch max. end stop torque 7 ncm max. 9.9 oz.-inch max. tightening torque of mountin g nut 25 ncm max. 2.2 lb-inch max. unit weight 1 g 3.5 10 -2 oz. terminals 3: pure sn shafts standard shaft 20 mm length (r or al code) an d 16 mm length (d or ag code) is measured from the mounting face to the free end of the shaft. vishay guarantee is lost if the customer modifies the shaft himself. hardware nuts and washer are supplied se parately (not mounted on the potentiometer) in a small bag placed in the packaging. environmental specifications temperature range -55 c to +125 c climatic category 55/100/56 sealing fully sealed - container ip67 marking vishay trademark model ohmic value code tolerance code manufacturing date code marking of terminals 3 the ohmic value is indicated by a 3 figures code: the first two digits are significant figures, the third digit is the multiplier: example: 101 = 100 102 = 1000 503 = 50 000 the manufacturing date is indica ted by a figures code. the firs t two digits are the year, the last two digits are the week. performance tests conditions typical values and drifts r t / r t (%) r 1-2 / r 1-2 (%) other electrical endurance 1000 h at rated power 90'/30' - ambient temp. 70 c 1 % 2 % contact resistance variation: 1 % climatic sequence phase a dry heat 100 c phase b damp heat phase c cold -55 c phase d damp heat 5 cycles 1 % 2 % - damp heat, steady state 56 days 40 c 93 % hr 1 % 2 % dielectric strength: 1000 v rms insulation resistance: > 10 4 m change of temperature 5 cycles -55 c at 100 c 1 % - v 1-2 /v 1-3 2 % mechanical endurance 10 000 cycles 3 % - contact resistance variation: 2 % r n shock 50 g s at 11 ms 3 successive shocks in 3 directions 0.5 % 1 % - vibration 10 hz to 55 hz 0.75 mm or 10 g s during 6 h 0.5 % - v 1-2 /v 1-3 1 %
p10 www.vishay.com vishay sfernice revision: 04-jul-17 4 document number: 51030 for technical questions, contact: sferpottrimmers @vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ordering information (part number) p10xxag103kb30 model style shaft resistance code tolerance code packaging code special number p10 xc xh xw xx ye ym yp ag = ? 3 mm to 16 mm (old code d) al = ? 3 mm to 20 mm (old code r) from 100 to 2 m 103 = 10 k k = 10 % on request: j = 5 % b30 = box 100 pieces (if applicable) given by vishay for custom design part number description (for information only) p10 xx ag 10k 10 % bo100 e3 model style shaft value tolerance special packaging lead (pb)-free related documents application notes potentiometers and trimmers www.vishay.com/doc?51001 guidelines for vishay sfernice resistive and inductive components www.vishay.com/doc?52029
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
